Book Instantly

Were you interested in know-how about A Step-by-Step Guide to Installing a Bathtub?

Setting up a bathtub isn't specifically rocket science, but it does call for solid plumbing, woodworking, as well as occasionally, tiling abilities. Changing an old tub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently available, the task can move easily; if you have to open up a wall to eliminate the old tub as well as position the brand-new bath tub, the task is a lot harder. In either case, the project is within a house handyman's abilities, although you will require an assistant to move out the old tub as well as embeded in the new one. Make certain you have actually certified on your own for the job as well as fit attempting it. As opposed to working with a professional to take control of a halfway-completed task, it is better to think about utilizing one prior to you begin. Chances are you may require a specialist plumber to make tube connections.
This short article will certainly aid you mount a new tub in your shower room if you have actually currently bought a new bathtub and don't need to alter the setup of your previous water supply pipes.
Your tools and material checklist must consist of the following:

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Measuring tape


• Pipeline Caps


 

Removing Old Touches

If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The procedure of eliminating the existing taps can be rather problematic as a result of the limited access that is often the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a towel prepared for the staying water that will come from the pipelines. As soon as the supply pipelines have actually been eliminated, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from transforming during this process. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old securing compound.
Before carrying on to fit the new faucets, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.

Fitting New Taps

If the tails of the new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin making sure that the washing machines are in place in between the tap as well as the sink. Secure the faucet in position with the maker provided backnut. Once the tap is securely in position, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet ports. The former kind ought to be attached to the tap ends initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.

Setting up the Bathtub

Utilizing both wood boards under its feet, place the tub in the called for setting. The wooden boards are practical in evenly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto 4 small factors.
The next goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the level and also changing the feet on the bathtub up until the spirit level checks out level.
To mount taps, fit all-time low of the furthest adaptable tap port to the appropriate supply pipeline by making a compression join; then do the exact same for the other tap.
Activate the water system and inspect all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill up the tub and likewise examine the overflow outlet as well as the normal outlet for leakages.
Finally, take care of the bathroom paneling as described in the maker's user's manual. Tiling as well as securing around the bath tub needs to wait until the tub has actually been used a minimum of when as this will settle it right into its final setting.

Planning for the Installation

First of all, the supporting structure supplied with the bathroom ought to be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to make certain that if the faucet comes with a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets unit to prevent stress on the tub.
Fit the adaptable faucet adapters to the bottom of the two taps using 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use every one of the provided washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently be ready to be fitted in its last placement.

Tiling Around the Tub

In the area where the bath fulfills the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to crack an inflexible seal, creating the water to pass through the wall surface in between the bath and the tiling, resulting in complications with dampness and also feasible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your components and also installations. They are offered in tubes and cartridges, and can securing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked paper or soft rope. Bear in mind to constantly fill the bathtub with water prior to sealing, to allow for the activity experienced when the bathtub is in use. The sealer can split fairly early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily offered on the market. It is suggested to fit the floor tiles utilizing water-resistant or water-proof sticky and cement.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

Do you really like reading up on A Step-by-Step Guide to Installing a Bathtub? Create feedback down the page. We would be pleased to listen to your responses about this posting. Hoping to see you back again soon. Feel free to take the opportunity to promote this content if you liked it. I treasure reading our article about How to Install a Bathtub.

Set Up An Appointment